Turbo Decoder supports all E series till 2014
E46/E53/E60/ E61 /E63 /E64/ E65/ E70/ E71/ E87/ E90/ E91/ E92/ E93
This turbo decoder also covers the below cars:
- Fiat and Lancia with HU 83 locks
- Land rover and Rover with HU 92 locks
- Peugeot Citroen with HU 92 locks
NO DAMAGE AT ALL TO LOCKS, UNTRACEABLE ENTRY, CHECK THEM OUT AT BELLOW LINK:
http://www.autodiagnostictools.co.uk/turbo-decoders/
THANKS FOR LOOKING !!!!
Thursday 29 January 2015
Tuesday 20 January 2015
Auto Diagnostic Tools UK
How to Install Rechargeable batteries and WIFI Card?
Notice: before we send
the package , we will put all the power out. So when you get it, you need to
host more than 4 hours charging, otherwise it will prompt you to charge is
low.
(1)— SD Connect multiplexer which need to input the batteries.
(2)— 6 units Ni-MH Rechargeable batteries, Size: AA, Voltage: 1.2V, Capacity: above 1700mA.
(3)—1 unit 108M WIFI Card.
(4)—Plum screwdriver, Specification: T20
Step two: Take out the rubber:
2.1 Use the T20 Plum screwdriver to take out the screw as below.
2.2 Take out the rubber as belwo.
(1)—Batteries Space.
(2)—WIFI Card Space
(3)—SD Card Space
Step three: Insert the Rechargeable batteries.
3.1 Use the T20 Plum screwdriver to take out the screw of Batteries Space fixation as below.
3.2 Take out the fixation of Batteries Space, pay attention to the Battery polarity marked in the Batteries Space.
3.3 Insert the batteries. Note the Battery polarity
3.4 Button on the Fixation of Batteries Space after inputting the Rechargeable battries.
3.5 Use the T20 Plum screwdriver to fix the screw of Batteries Space fixation as below. Inserting the batteries is finished.
Step four: Installing WIFI Card
4.1 Inserting the WIFI card into the WIFI Card Space. Please make the correct direction.
4.2 Push it to make it totally connected.
4.3 Cover the rubber and fix the screws to finish all the work.
How to Install Rechargeable batteries and WIFI Card?
Step one: Please prepare the following tools.(1)— SD Connect multiplexer which need to input the batteries.
(2)— 6 units Ni-MH Rechargeable batteries, Size: AA, Voltage: 1.2V, Capacity: above 1700mA.
(3)—1 unit 108M WIFI Card.
(4)—Plum screwdriver, Specification: T20
Step two: Take out the rubber:
2.1 Use the T20 Plum screwdriver to take out the screw as below.
2.2 Take out the rubber as belwo.
(1)—Batteries Space.
(2)—WIFI Card Space
(3)—SD Card Space
Step three: Insert the Rechargeable batteries.
3.1 Use the T20 Plum screwdriver to take out the screw of Batteries Space fixation as below.
3.2 Take out the fixation of Batteries Space, pay attention to the Battery polarity marked in the Batteries Space.
3.3 Insert the batteries. Note the Battery polarity
3.4 Button on the Fixation of Batteries Space after inputting the Rechargeable battries.
3.5 Use the T20 Plum screwdriver to fix the screw of Batteries Space fixation as below. Inserting the batteries is finished.
Step four: Installing WIFI Card
4.1 Inserting the WIFI card into the WIFI Card Space. Please make the correct direction.
4.2 Push it to make it totally connected.
4.3 Cover the rubber and fix the screws to finish all the work.
Subscribe to:
Posts (Atom)